{"id":951,"date":"2026-09-17T11:47:14","date_gmt":"2026-09-17T11:47:14","guid":{"rendered":"https:\/\/mytrueblinds.com\/?page_id=951"},"modified":"2026-09-17T12:01:12","modified_gmt":"2026-09-17T12:01:12","slug":"how-to-install","status":"publish","type":"page","link":"https:\/\/mytrueblinds.com\/index.php\/how-to-install\/","title":{"rendered":"How to install"},"content":{"rendered":"\n
\"\"<\/figure>\n\n\n\n


Installing different types of window treatments requires specific techniques depending on whether you want an inside mount<\/strong> (mounted inside the window frame recess) or an outside mount<\/strong> (mounted on the wall or trim outside the frame)<\/mark>.<\/p>\n\n\n\n

Below are complete, step-by-step instructions for installing drapery, blinds, shades, plantation shutters, and motorized systems.<\/p>\n\n\n\n

\n\n\n\n

\ud83e\uddf0 General Preparation & Tools<\/p>\n\n\n\n

Before beginning any installation, gather these common tools:<\/p>\n\n\n\n

    \n
  • Measuring tape & Pencil<\/li>\n\n\n\n
  • Power drill or electric screwdriver<\/li>\n\n\n\n
  • Appropriate drill bits (typically 1\/8-inch for pilot holes)<\/li>\n\n\n\n
  • Spirit level (critical for preventing uneven hanging and motor wear)<\/li>\n\n\n\n
  • Drywall anchors (essential if you are not drilling directly into wood studs)<\/li>\n\n\n\n
  • Step ladder<\/li>\n<\/ul>\n\n\n\n
    \n\n\n\n

    1. How to Install Drapery (Curtains)<\/p>\n\n\n\n

    Drapery is almost always an outside mount<\/strong>. For a standard installation:<\/p>\n\n\n\n

      \n
    • Step 1: Measure and Mark Height.<\/strong> Decide where the drapery rod will sit. To make windows look taller, hang the rod 4 to 6 inches above the window frame (or even halfway to the ceiling). Use your level and tape measure to mark the bracket heights.<\/li>\n\n\n\n
    • Step 2: Mark Bracket Width.<\/strong> Measure the width of your window and add 3 to 6 inches to each side. This allows the curtain panels to pull back without blocking the window glass. Mark the exact placement of your mounting screws through the bracket holes.<\/li>\n\n\n\n
    • Step 3: Drill and Anchor.<\/strong> Drill pilot holes at your marks. If you hit drywall instead of wood, tap in your plastic wall anchors.<\/li>\n\n\n\n
    • Step 4: Mount the Brackets.<\/strong> Align the brackets over the holes or anchors and secure them firmly using your power drill and screws.<\/li>\n\n\n\n
    • Step 5: Hang the Drapery.<\/strong> Feed your drapery panels onto the rod (or slide on your curtain rings). Place the rod onto the brackets, tighten any set screws on the brackets to lock the rod in place, and screw on the decorative finials at both ends.<\/li>\n<\/ul>\n\n\n\n
      \n\n\n\n

      2. How to Install Blinds (Faux Wood, Wood, or Aluminum)<\/p>\n\n\n\n

      Blinds can be inside or outside mounted. These instructions focus on the popular inside mount<\/strong>:<\/p>\n\n\n\n

        \n
      • Step 1: Position the Mounting Brackets.<\/strong> Inside mount blinds use box brackets installed in the top left and right corners of the window frame. Hold the left bracket up inside the corner. Ensure the front drop-down gate faces out toward the room. Mark the screw holes (either into the top or the side of the frame). Repeat for the right side.<\/li>\n\n\n\n
      • Step 2: Add Center Support (If Needed).<\/strong> If your blinds are wider than 48 inches, a center support bracket is usually required. Place it slightly off-center so it won’t interfere with the internal blind cords or mechanisms.<\/li>\n\n\n\n
      • Step 3: Drill and Secure.<\/strong> Drill pilot holes at your marked locations and securely screw the brackets into place.<\/li>\n\n\n\n
      • Step 4: Insert the Headrail.<\/strong> Open the front gates of the box brackets. Slide the metal headrail of the blinds into the brackets. Close the bracket gates until they snap shut securely.<\/li>\n\n\n\n
      • Step 5: Attach the Valance.<\/strong> Clip the provided plastic valance clips onto the front of the headrail before hanging, then snap the decorative wood or faux-wood valance fascia into the clips to cover the bare metal rail.<\/li>\n<\/ul>\n\n\n\n
        \n\n\n\n

        3. How to Install Shades (Roller, Cellular, or Roman)<\/p>\n\n\n\n

        Shades are lightweight and typically use universal click-in top brackets. These instructions apply to both inside and outside mounts:<\/p>\n\n\n\n

          \n
        • Step 1: Space Out the Brackets.<\/strong> Measure 4 inches in from each side of where the headrail will sit and mark the location. If a third center bracket is provided for wider shades, space it evenly between the two outer marks.<\/li>\n\n\n\n
        • Step 2: Align and Level.<\/strong> Hold the brackets up to your marks. Ensure they are perfectly aligned horizontally using a spirit level (an uneven shade will telescope or fray at the edges when rolling). Mark the screw holes.<\/li>\n\n\n\n
        • Step 3: Secure the Brackets.<\/strong> Drill pilot holes and screw the brackets into the top of the window frame (inside mount) or onto the wall\/molding (outside mount).<\/li>\n\n\n\n
        • Step 4: Mount the Headrail.<\/strong> Position the front lip of the shade’s headrail into the front hooks of the mounting brackets. Pivot the back of the headrail upward and push firmly until you hear it click or snap into place.<\/li>\n<\/ul>\n\n\n\n
          \n\n\n\n

          4. How to Install Plantation Shutters<\/p>\n\n\n\n

          Shutters are unique because they include a built-in outer frame that holds the operable shutter panels. They are most commonly installed as an inside mount<\/strong>:<\/p>\n\n\n\n

            \n
          • Step 1: Assemble the Shutter Frame.<\/strong> Lay the four pieces of the shutter frame (top, bottom, left, right) face down on a clean, carpeted surface or blanket. Align the corners and insert the provided corner keys or mechanical fasteners to lock the outer frame together.<\/li>\n\n\n\n
          • Step 2: Insert Frame and Level.<\/strong> Place the fully assembled frame into the window opening. Use a spirit level to check all sides. If the window frame is slightly out of square, insert small plastic shims behind the shutter frame until it sits perfectly level and plumb.<\/li>\n\n\n\n
          • Step 3: Fasten the Frame.<\/strong> Pre-drilled holes are usually located inside the frame tracking. Drive a screw through the left and right frame sides into the window casing. Do not tighten completely yet.<\/li>\n\n\n\n
          • Step 4: Hang the Shutter Doors.<\/strong> Lift the shutter doors\/panels up and align their factory-installed hinges with the hinges on the frame. Drop the hinge pins straight down into place to hang the doors.<\/li>\n\n\n\n
          • Step 5: Adjust and Square.<\/strong> Close the shutter doors and inspect the spacing (or “shadow gap”) around the perimeter. If the doors unevenly meet in the middle, adjust the frame slightly or add\/remove shims. Once square, tighten all frame screws completely and snap on any provided button covers over the screw holes.<\/li>\n<\/ul>\n\n\n\n
            \n\n\n\n

            5. How to Install Motorization & Automation<\/p>\n\n\n\n

            Modern motorized window treatments follow the same physical bracket installations listed above, but require electrical and digital programming setup.<\/p>\n\n\n\n

              \n
            • Step 1: Pre-Charge the Motor.<\/strong> If your shades or blinds use a rechargeable built-in lithium-ion battery, plug the motor into its charger and let it reach a full 100% charge before<\/em> mounting the treatment to the window.<\/li>\n\n\n\n
            • Step 2: Manage the Wires & Antennas.<\/strong> When clicking a motorized headrail into its brackets, make sure no internal power cords are pinched. If your motor utilizes a small wire antenna, ensure it hangs slightly exposed and is not tucked tightly behind a thick metal headrail, as this severely blocks the wireless remote control signal.<\/li>\n\n\n\n
            • Step 3: Connect External Power (Optional).<\/strong> If you are not using rechargeable batteries, plug your shade into an adjacent wall outlet, mount the external wand battery pack behind the headrail, or attach the slim solar panel wire to the glass-facing side of the shade.<\/li>\n\n\n\n
            • Step 4: Program the Upper and Lower Travel Limits.<\/strong>\n
                \n
              1. Grab the wireless remote paired to the shade.<\/li>\n\n\n\n
              2. Press the Program\/Pairing button<\/strong> on the back of the remote (or on the shade’s motor cap) until the motor gives a quick physical nudge or beep.<\/li>\n\n\n\n
              3. Use the Up arrow<\/strong> to roll the shade to your desired top limit. Press the designated limit-save button combination on your remote to lock it in.<\/li>\n\n\n\n
              4. Use the Down arrow<\/strong> to lower the shade to where it perfectly meets the windowsill. Press the limit-save combination again to set the bottom limit.<\/li>\n<\/ol>\n<\/li>\n\n\n\n
              5. Step 5: Connect to a Smart Hub (Optional).<\/strong> If using smartphone or voice control, plug your manufacturer’s smart bridge or hub into a wall outlet near your router. Open the corresponding mobile app, select “Add Device,” and follow the app’s prompt to hold the button on your shade’s remote until the hub pairs with the window treatment.<\/li>\n<\/ul>\n\n\n\n

                <\/p>\n","protected":false},"excerpt":{"rendered":"

                Installing different types of window treatments requires specific techniques depending on whether you want an inside mount (mounted inside the window frame recess) or an outside mount (mounted on the wall or trim outside the frame). Below are complete, step-by-step instructions for installing drapery, blinds, shades, plantation shutters, and motorized systems. \ud83e\uddf0 General Preparation & Tools Before beginning any […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"class_list":["post-951","page","type-page","status-publish","hentry"],"jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/mytrueblinds.com\/index.php\/wp-json\/wp\/v2\/pages\/951","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/mytrueblinds.com\/index.php\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/mytrueblinds.com\/index.php\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/mytrueblinds.com\/index.php\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/mytrueblinds.com\/index.php\/wp-json\/wp\/v2\/comments?post=951"}],"version-history":[{"count":4,"href":"https:\/\/mytrueblinds.com\/index.php\/wp-json\/wp\/v2\/pages\/951\/revisions"}],"predecessor-version":[{"id":960,"href":"https:\/\/mytrueblinds.com\/index.php\/wp-json\/wp\/v2\/pages\/951\/revisions\/960"}],"wp:attachment":[{"href":"https:\/\/mytrueblinds.com\/index.php\/wp-json\/wp\/v2\/media?parent=951"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}